Three Vital Air Compressor Safety Guidelines

Do you have or have a friend who has an air compressor? These units are traditionally used in lots of industrial settings and manufacturing services, and also are located in residential homes and small businesses where they are utilized to inflate vehicle tires and operate air power equipment. The absence of regular maintenance and inspection of air compressors often accident took place.

The phrase “air compressor” is normally utilized to identify the compressor motor along with the air receiver tank. However, formally the air compressor is the motor that compresses air, generally placed on the surface of a vertical, or horizontal air receiver. The compressor motor needs service and maintenance -- go through manufacturer's needs.

Below are a few things you require to understand in case you have an air compressor unit set up in your organization or home:

Drain air receiver tank regular

Water is a normal by-product of compressed air. It usually forms within the tank. The condensation that forms within the tank needs to be drained daily to avoid the buildup of condensation. Water kept undrained in a pressure vessel can cause rust and probable early failure or, at worst, devastating failure from a damaged tank bottom. Owners should consider adding a timed automatic drain so daily draining takes place routinely.

Check out regularly

When draining built-up condensation, successfully examine the fluid getting drained. Rusty, scaly water is a positive symptom of active corrosion. If inside corrosion is suspected, take away the vessel from service, take out a plug or fitting from the tank, and confidently examine the inner shell and head areas. The view is restricted and a borescope examination camera may be needed. Outside the body, connection welds obtaining the compressor motor and saddle as well as leg supports must be checked for any early indications of vibration-induced cracking. The tank shell and heads must also be free from any physical damage.

Check pressure release valves

The pressure release valve, that protects the air receiver from being over-pressurized, may be compromised through dirt, oil, and other pollutants so it should be regularly examined and tested. Every vessel must have a nameplate that information the highest allowed functioning pressure. Make sure the fixed pressure of the safety valve does not surpass that permitted on the vessel nameplate and ensure that the capability of the safety valve is larger than the capacity of the air compressor.

Important thing?
Air compressor tanks may look great on the exterior, but hidden inside damage can cause critical risks. If uncertain, switch your unit. When changing units, always dispose of them appropriately.



View more here: An Ideal Guide to Sizing The Air Receiver Tank

Read more: Promec Engineering Pty Ltd

How The Australian Steel Industry Reacts With COVID-19

Australia continues to carefully monitor the outbreak of coronavirus (COVID-19). Cases of the COVID-19 virus are increasing in Australia, and the situation is changing fast. You can get up to date information from australia.gov.au.

According to a special Roy Morgan Snap, SMS Survey in the middle of March over 60% of Australian businesses report being affected by the COVID-19 coronavirus, and 78% of manufacturing industries have been affected particularly difficult by the virus.

Safe Work Australia advises every workplace what to do to maintain workers safe at their workplace and reduce the chance of exposure to COVID-19 in the workplace.

• If possible permit workers to work from home.
• Maintain physical distance with a minimum of 1.5 meters among workers.
• Maintain the practice of good hygiene, inspire all workers to regularly wash their hands for a minimum of 20 seconds with water and soap or utilizing hand sanitizer.
• Understand how to identify COVID-19 symptoms like fever, cough, sore throat and shortness of breath.
• Make sure workers do not come to work when they are sick to ensure that your workplace is regularly cleaned and sanitized.
• Get signs and posters around the workplace to remind workers as well as others to understand the hazards of COVID-19, and it is essential to prevent its spread.

Australian Steel Institute (ASI) announces an update on business activities in the Australian steel industry in this situation. The key steel companies have confirmed that their supply chains are operating normally.

To stop the spread of COIVD-19 the steel industry already procedures very high standards of hygiene to protect all employees from schedule work safe practices risks. These procedures have been galvanized and heightened because of the outbreak of the COVID-19 pandemic.

The Australian steel industry is more than willing to perform its part in containing COVID-19. Australian steel manufacturers have already released this procedure to protect their workers:

• Steel manufacturers along with other services like steel fabrication have introduced strict entry processes, such as screening for COVID-19 exposure and examining the temperatures of workers.
• Stricter than normal hygiene methods, use heightened, more repeated, and deeper cleaning.
• Review of amenities to make sure social distancing rules are stringently followed, such as keeping 1.5m among workers always and the reduction of overlapping shifts.
• Stringent return to work practices post-travel and where a worker feels sick, such as self-isolation.
• Prepare remote working plans for non-essential workers.
• Increased communications around all hygiene steps to help make sure workers, service providers, and supplier compliance.
• Implement of in-depth processes to control the COVID-19 exposure case.